![]() ![]() Do not remove the top knot in the string (above the black bead) from the string as this will fail to hit the lowest limit switch inside of the unit (this is responsible for letting the unit know when to stop and start the motor to move the door) and cause damage to the motor. The door fitted to the automatic door opener should not exceed 1kg and have a minimum weight of 300g. Please pay important attention to which way the batteries have been inserted, making sure that they match the appropriate and respect + - signs. This should not exceed the 1KG limit as this can cause damage to the motor and/or snap the string. If testing a unit without a door attached, you will need to attach something to the end of the string of similar weights (a minimum of 300g and a maximum of 1KG). Testing the unit without a door attached: The use of these buttons has the primary use of testing the door and aiding with restringing.Ĥ. Please note this is not a complete override of the settings, and the door will turn to its previous start after a short period of time (approx. If you want to test or force the door open at anytime you can use the + button, likewise, to test or force the door close at anytime you can press the - button. To test/force the door open or close at anytime: You will now need to reset your door opener to the program and times you desireģ. Press the + button to wind the string onto the spoolġ5. Attach a weight of 300g-1KG to the end of the stringġ4. Replace the battery and front panel of the unitġ3. Replace the yellow bar with the screws - making sure the string is underneath itġ2. Pass the string underneath the motor spool and back over the top, tying it around the spindle screwġ1. Remove the screws from the small yellow bar and thread the string through the two cyclindersġ0. Insert the string through the yellow rectangle bar at the bottom of the circuit boardĩ. Thread the replacement string through the bottom hole of the unitħ. Swing the front panel down to the right to allow access to the stringĦ. Remove a battery in order to stop the motorĤ. Remove the 4 screws from the front of the door opener unitģ. Restringing a CUBE model (shaped like a cube)Ģ. Once the string has been wound up, you will need to reset the unit to the times and program you desire ![]() Wind string on to motor spool by pressing the + button onlyġ4. Attach a weight of 300g-1kg to the stringġ3. Replace the back of the unit using the screws from earlierġ2. Ensure the string is inserted through the hole at the bottom of the unitġ1. Reconnect the battery wire to the circuit board in the door openerġ0. Pass the string underneath/behind the motor spool and over the top and then tie string around the spindle screwĩ. Ensure the string is passed to the left of the white cylinder.Ĩ. Follow the white line on the circuit board and thread through the eyelet on the rightħ. Insert the new string through the white rectangle bar at the bottom of the circuit boardĦ. Remove the battery wire from the circuit board (black and red wire that go into a white plug - 'BAT' is written next to it)ĥ. Remove the 5 screws from the back of the unitģ. Remove the door opener from the coop by unscrewing the four screwsĢ. ![]() A Frame Run for Alexandria Chicken Coops Size-Color - 9 ft. Hentronix makes several door opener/closers More from RedDrgn. Hentronix Automatic Door Opener and Closer. Restringing ELITE door openers (shaped like a house if you aren't certain which one you have!)ġ. Pullet-Shut Automatic Chicken Door Added by RedDrgn Create date Updated May 15, 2017. One of the common mistakes when restringing out units is not having the string coming through underneath the motor spool (the arm where the string should be attached to). 70 minutes.įor our units to work at their best the string inside of the door opener needs to be in a specific manner. Much older units (3 years or older) can be reset in a shorter period of time approx. Returning the unit back to factory settings:Īs a rule of thumb, we suggest to our customers to return the unit back to factory settings by removing the batteries from the unit for 72 hours. I really hope they take this request into consideration so that it might help other chicken owners as well.Here are a few suggestions to try troubleshooting your automatic door opener:ġ. I use a smart coop light in my other coops and control the light with a schedule within the Phillips Hue app, but I didn't have electrical to add to my newest coop, so I chose to use the Omlet Coop light with the auto door. This way you could have the light come on independently of the door so they had plenty of time to get in and get comfy before the door closes. It is set to come on 5 minutes before the door closes, but for Silkies they are so stubborn - it would be nice to be able the coop light to come on and go off on a separate schedule from the door. The only thing I wish was that there could be a separate auto program for the coop light. It was so simple and I liked it so much that when it was time to get an auto door for my Silkie Coop this was my go to door. I have three automatic coop doors for my coops and this one was the easiest and fastest install. This door is amazingly simple to install and use.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |